例句與造句

1. Not to be under estimated is the human error factor
   不要低估人的錯誤因素。
2. Identification of human error factors in venture capital
   風險投資中人因失誤因素的識別研究
3. It can optimize the process of piezoresistive sensor calibration and compensation , then , a total error factor within 0 . 2 % of the sensor s repeatability errors is obtained
   通過該芯片的補償，可以使硅壓阻式傳感器的重復性誤差小于0 . 2 % 。
4. The impact of the effective resist diffusion length to the exposure latitude and mef ( mask error factor ) for the 0 . 13 m photolithography and beyond is presented
   展示了在0 . 13 m及以下工藝中等效擴散對能量裕度和掩模版誤差因子的影響的研究結果。
5. The issues of consistency , temperature shift and non - linearity are solved by the system which is composed of hardware and software . an output error factor of silicon piezoresistive sensor is achieved within 0 . 2 %
   該系統由硬件和軟件兩部分組成,主要解決了它的一致性、溫度漂移和非線性等問題,使硅壓阻式傳感器的輸出精度達到了0 . 2 %以內。
6. It's difficult to find error factor in a sentence. 用error factor造句挺難的
7. The mca7707 is a special sensor signal processor optimized for piezoresistive sensor calibration and compensation . achieving a total error factor within 0 . 2 % , the mca7707 compensates temperature errors and non - linearity of silicon piezoresistive sensors
   Mca7707是一種專用傳感器信號處理器，它可以補償硅壓阻式傳感器的溫度誤差和非線性誤差，使傳感器總的精度達到0 . 2以內。
8. With the development task background of ctr200g precision centrifuge , the acceleration error factors of centrifuge system are qualitatively analyzed theoretically at first and also quantitatively calculated by means of finite element method , therefore , the structural optimum design problem of the load pan is proposed
   論文以“ ctr200g型精密離心機”的研制任務為背景,首先從理論上對引起離心機系統加速度誤差的因素進行了定性分析,并且采用了有限元方法對其進行了定量計算,由此提出了負載盤結構優化設計的問題。
9. Identified human error factors by using multi - view human error factor identification method , set up a detailed factor distinguish form ; divided the behavior of people into 5 periods of stage , namely systematic state monitor stage , state analyse stage , goal analyse stage , scheme confirm stage and behavior carry out stage , analysed the possible causes and modes of human error at each stages separately ; take organization ' s view as an example , according to human error factor distinguishing , human error causes and modes analysis results , explained the construction course of the factor tree , and got an intact human error factor tree finally
   摘要運用人誤因素辨識多視圖法進行因素辨識，建立了詳細的因素辨識表；把人的行為分為系統狀態監測、狀態分析、目標分析、方案確定和行為執行5個階段，分別各個階段可能的人誤原因及模式；根據因素辨識和人誤原因及模式，分析結果，以組織視圖為例闡述人誤因素樹的構建過程，最終得到了一個完整的人誤因素樹。
10. What flow is that , we use model simulation to analyze the em algorithm contraction ratio . through network simulating , we analyze the factors which can influence loss inference algorithm accuracy like measurement strategy or routing algorithm . we analyze the accuracy and contraction characteristic of multicast - based direct algorithm and em algorithm , and compare the error factor between them
    實驗中通過網絡仿真模型,確定了em算法的收斂速率;研究了不同測量策略和路由器擁塞避免算法對丟包率推理算法準確率的影響;分析了單點多播的de和em算法準確性、收斂性等特征,通過比較兩種算法的統計誤差,得出em算法略優于de算法的結論。
11. In order to establish properly testing system , instrument bus such as gpib and vxi , and corresponding instrument language such as scpi are also specified . 3 . the measurement result and corresponding error factor are gived . the uncertainty of measurement result are discussed and some formal data files are also formed
    要實現的最終目標是建立一套針對于中電29所研制的雷達變頻組件的測試裝置,并建立相應的不確定度分析文件,對已有雷達變頻組件的性能參數進行綜合的檢定。
12. This paper presents a wider research field - risk analysis . through the study of the effects that threat factors and error factors impact on the flight risk and adjusting performance rules , the horizontal safe corridor , threat avoidance , vertical altitude real - time modification and the fastest trajectory programming are progressed
    總結前人在該方面的研究成果，提出一個更加廣義的研究角度? ?風險分析。通過對威脅因素、誤差因素對飛行風險的作用，調整性能準則而進行了水平安全走廊設計、威脅回避、垂直離地高度實時修正以及最快速航跡規劃。
13. Nowadays , the machining center carries through the precision inspection only following the fixed coordinates " axes , which can not completely reflects the real error of the spacial position of the practical machining outside the axes and leads to having no the directive relation between the inspected precision and the practical machining precision . so , this paper introduces that the error factors of influencing workpiece ' s outline on machining and carries out the solid inspection of every spot ' s error inside the workaround on the horizontal machining center
    本文針對當前加工中心僅沿固定的坐標軸線進行精度(含幾何精度和定位精度)檢驗，并不完全反映軸線外實際加工的空間位置真實誤差，導致檢出精度與機床實際加工精度無直接對應關系的現狀，論述了加工時影響工件型面輪廓精度之加工中心的誤差因素，對加工中心實施其工作區內各點誤差的立體檢測。